This selection of Rode miniature lavalier (tie-clip) microphones have been designed to provide broadcast quality audio in a variety of situations including studio and location work.
The mics, with omni-directional condenser capsules, can be connected to a variety of branded wireless systems, cameras, and portable recorders by using the applicable MiCon connector.
Lavalier - Condenser, omni-directional, MiCon connector
abgekündigt
Rode Lavalier is a 2.54mm omni-directional condenser capsule housed in a black casing designed for film, television, and house of worship use. A frequency response of 60Hz to 18kHz and the included mini-furry windshield help retain voice nuances in adverse conditions. The 1.2 metre black Kevlar reinforced detachable cable has a sub-miniature screw to connect to any one of the MiCon series connectors. Connectors are not included and should be ordered separately, see below.
Included accessories: Minifur-Lav artificial fur windshield, Lav-Clip mounting clip, WS-Lav pop filter, Anti-Trauma case, and spanner.
Capsule size: 2.54mm. Frequency range: 60Hz to 18kHz. Output impedance: 3000ohms. Maximum SPL: 110dB. Sensitivity: -33.5dB. Weight 1g. Dimensions: 12 x 4.5 x 4.5mm (h x w x d).
Lavalier II - Condenser, omni-directional, 3.5mm locking jack
Rode Lavalier II has been designed for 'the most demanding applications' including film, television, and field recording. A frequency range of 20Hz to 20kHz with almost flat response allows the user to capture 'broadcast-grade' audio from an omnidirectional polar pattern. Lavalier II is compatible with Rode Wireless GO, Rode Wireless GO II, Rode AI-Micro, and RODELink series wireless.
Included accessories: Pop filter, mic clip, mini furry windshield, set of coloured ID rings, and zip case.
Capsule size: 6mm. Frequency range: 20Hz to 20kHz. Output impedance: 2000ohms. Signal to noise ratio: 66dB. Maximum SPL: 106dB, RMS 1% THD; 120dB, RMS 10% THD. Sensitivity: -37dB, 1V/Pa, +/- 3dB. Dynamic range: 78dB. Power requirements: 1.8V to 5V plugin power. Dimensions (LxWxH): 1200 x 10 x 5mm, microphone; 21 x 20 x 8mm, clip. Weight: 9g, microphone; 2g, clip.
Pinmic - Condenser, omni-directional, MiCon connector
abgekündigt
This has many of the characteristics of the 'Lavalier' microphone, including the 2.54mm omni-directional condenser capsule and the 60Hz - 18kHz frequency response. The 9mm deep, and 11mm diameter capsule head comes with a black housing that can be switched for an included paintable silver mesh. A pin-through design where the microphone's back plate is hidden behind the fabric, makes it easier to conceal than a lapel style microphone. Mounts through fabric up to 1.5mm thick. 'DeadMouse-Pin' fur windshield reduces unwanted noise caused by wind and adverse conditions. The 1.2 metre black Kevlar reinforced cable has a sub-miniature screw to connect to any one of the MiCon series connectors. Connectors are not included and should be ordered separately, see below.
Included accessories: Clip1 MiCon cable clip, 1x unpainted mesh head, Anti-Trauma case, tool kit, DeadMouse-Pin fur windshield.
Capsule size: 2.54mm. Frequency range: 60Hz to 18kHz. Output impedance: 3000ohms. Maximum SPL: 110dB. Maximum output level: 189.0mV. Sensitivity: -33.5dB. Weight 10g. Dimensions: 16 x 22 x 33mm (h x w x d).
Pinmic Long - Condenser, omni-directional, MiCon connector
abgekündigt
Has all the characteristics of the PinMic, however it has a longer pin and therefore it is suitable for thicker fabrics up to 3.5mm thick.
Specifications and accessories are as for the Pinmic above.
Mounts and Windshields
Designed to give the lapel microphone protection from windy conditions when on location the Minifur-Lav is manufactured from synthetic fur and compatible with the Rode Lavalier, smartLav and smartLav+, a handy accessory for outdoor use. Supplied in pack of three. Dimensions: 26 x 44 x 44mm (h x w x d). Weight: 1g.
Available as pack of three (74-2412) or pack of ten (74-2411) InvisiLav has been designed to help the user conceal the positioning of their Lavalier or smartLav microphone by allowing adhesion to skin or fabric. Two mounting points allow for a redundant microphone if required, and the soft, medical grade, skin safe, material absorbs noise and vibration giving a cleaner audio signal. Dimensions: 18 x 25 x 6mm (h x w x d). Weight: 5g.
A 'dual-toothed' clothing pin designed as an accessory for Rode Lavalier, smartLav, smartLav+, and Lavalier GO. Supplied as single piece measuring 16 x 7 x 12mm (HxWxD), and weighing 1g. Colour: Black.
An alligator style lavalier microphone clip, also known as CLIP2, that has been designed as a spare or accessory for Rode Lavalier, smartLav, smartLav+, and Lavalier GO. Supplied as a pack of three with each clip measuring 24 x 11 x 27mm (HxWxD) and weighing 3g.
Micon Extension Cables and Connectors
Made with Kevlar-reinforced cable to extend the reach of the captive cable of the Lavalier, PinMic, or PinMic Long microphones. these are terminated with MiCon-compatible, sub-miniature screw and socket connectors, 1.5mm in diameter. They are offered in 1.2 and 3 metre lengths and various colours.
Micon-1 Connector - Jack, 3.5mm, 3-pole with locking ring - Sennheiser transmitter
An optional adapter to connect the Rode HS1 headset and Lavalier, PinMic, or PinMic Long microphones to a Sennheiser wireless transmitter with locking 3.5mm TRS jack socket. Dimensions: 39 x 10 x 10mm (h x w x d). Weight: 10g.
Micon-2 Connector - Jack, 3.5mm, 3-pole - Stereo devices
An optional connector designed to connect the Rode HS1 headset and Lavalier, PinMic, or PinMic Long microphones to a standard 3.5mm TRS jack with a power supply of 1V minimum. Dimensions: 37 x 10 x 10mm (h x w x d). weight: 8g.
Micon-3 Connector - TA4F, 4-pin mini (XLR) - Shure transmitter
An optional connector designed to connect the Rode HS1 headset and Lavalier, PinMic, or PinMic Long microphones to select Shure transmitters with TA4F four-pin mini connector. Dimensions: 36 x 13.65 x 10.4mm (h x w x d). Weight: 10g.
Micon-4 Connector - 4-pin female with locking ring - Audio-Technica transmitter
An optional connector designed to connect the Rode HS1 headset and Lavalier, PinMic, or PinMic Long microphones to an Audio Technica UniPak body-pack wireless transmitter with a locking 4-pin female connector. Dimensions: 36 x 11.6 x 11.6mm (h x w x d). Weight: 13g.
Micon-5 Connector - XLR, 3-pin, male - Standard microphone input
abgekündigt
An optional connector designed to connect the Rode HS1 headset and Lavalier, PinMic, or PinMic Long microphones to a standard, 3-pin XLR, female input with phantom power. Dimensions: 61.8 x 30.1 x 21mm (h x w x d). Weight: 50g.
Micon-8 Connector - Jack, 3.5mm, 3-pole with locking ring - Sony transmitter
An optional connector designed to connect the Rode HS1 headset and Lavalier, PinMic, or PinMic Long microphones to a Sony UWP transmitter with a locking 3.5mm jack. Dimensions: 39 x 10 x 10mm (h x w x d). Weight: 10g.
Micon-11 Connector - Jack, 3.5mm TTRS - Smart phones
An optional connector designed to connect the Rode HS1 headset and Lavalier, PinMic, or PinMic Long microphones to a device with 3.5mm TTRS jack socket such as an iPhone, iPad, and select Android devices. Dimensions: 1200 x 9 x 9mm (h x w x d). Weight: 7g.